A hinge can often work loose, binding the door against the frame. If you took the door off the hinges to paint it, the problem may be you didnt line it back up properly when putting it back on, though its not unheard of for coats of paint to cause the same issue. If you took the door off the hinges to paint it, the problem may be you didnt line it back up properly when putting it back on, though its not unheard of for coats of paint to cause the same issue. Press question mark to learn the rest of the keyboard shortcuts. Then re-nail the door-stops on leaving a 1-2mm gap all the way around to allow for paint (fix them tighter if no decorating needs doing afterward). Put a longer screw in and see if it will pull the door further in allowing it to close. Thick paint may make a door too big for the frame, and, as a result, the paint will stick to the frame when the door is closed. How To Paint a Door So That It Won't Chip or Peel. Sticking Doors or Doors that Won’t Close. If you took the door off the hinges to paint it, the problem may be you didnt line it back up properly when putting it back on, though its not unheard of for coats of paint to cause the same issue. We have 6 or 7 more doors to paint, but they're all previously painted so one coat should do it. Sometimes when you close a door the top for example will touch the doorstop and it will feel closed but then you have to push the handle hard for the latch to actually click, locate and hold the door shut. Door won't close after painting how to fix an uneven a that stay closed straighten frame hang in crooked adjusting hinges correct gap adjust self closing hinge tension youtube on 55 ford 2002 sierra - eastcoastrapist.com I'll have to ask if he painted the top. New comments cannot be posted and votes cannot be cast, A forum oriented towards trades-oriented painting & finishing techniques, products and support. Detach the door by using a screwdriver and a hammer to remove the hinge pins. Ask Question Asked 5 years, 4 months ago. I am hopeful they will endure over time, but I can’t be certain. Just sand down the top of the door until it fits through again. Subscribe to our free real estate newsletter at pages.email.bostonglobe.com/AddressSignUp. The old hinges are 3½ inches, and the new ones are the same size. Doors that bind or will not close properly are a common problem. If the hinge leaf and the mortise were not aligned so that the hinge leaf was fully seated in the mortise when the screws were driven, there will be a compression mark from the hinge. Then place the wax paper between the two surfaces before closing the door for the night. Other times, one or more hinge mortises are too deep and need to be shimmed or re-cut. On the latch side, a door is cut at a slight bevel to make it easier to close. MOXIE. If this is the case, you will probably see telltale signs of scraped paint on the door where it rubs. It's the top that's sticking, can we get a planer and get it shaved down to fit? When a door latch won’t catch, it’s because the latch doesn’t align with the hole in the strike plate. Take a sanding block and just hit the top of the door. Three coats of paint is a pretty thick layer, which could take up that extra space between the door and the frame. Seconding this. A. But frequently the solution is on the hinge side. Shut the door and look and see if you have a gap 1/4 inch will work, between the door frame and the hinge side of the door. Before trying to trim the door, open it and examine the hinges. I doubt it since the door was already hung. A hinge leaf that isn’t flush with the jamb face can prevent a door from operating properly. As a result of this some of the doors no longer close, i.e. Before trying to trim the door, open it and examine the hinges. Q. I am repainting all of our first-floor doors and replacing the existing painted-over hinges. Before filling holes or priming, scrub the entire door with heavy-duty household cleaner. Run your finger over the jamb and hinge as well as the door edge and hinge to ensure that the hinge is flush with both surfaces. Can anyone explain this? Just painted 7 interior doors and their jambs. Also check for grime or any sticky buildup that may just need to be cleaned. Look at the space around the door. The ideal is a 1/8-inch gap between the door and jamb at all points. Depending on the type of door you have (usually wood) the steps will vary for fixing and repairing your exterior door. Is there anything I can do other than put the old hinges back on? I replaced the 3.5" hinges on an interior door with hinges of the same size. First score the paint line where the stop meets the jamb. Now that we are finished, the entry door does not close. If so, you just need a screwdriver to fix it.To fix the cabinet door, life the door into place and gently tighten the screws with a screwdriver until it’s snug against the wood. However there is usually enough clearance on a door for it to open and close after being painted. A hour seems short but at the same time im sure ive done it just as quickly before. Send your questions to [email protected] or tweet them to @robertrobillard. If you have a popcorn ceiling, get it tested before you do any work, and if the results are positive, have the repairs performed by an asbestos-removal professional. Replaced door hinges and now the door won't close - hits the door stop on the hinge side. As a result, the door may scrape the door frame when closing, or may no longer properly meet the latch-side strike plate. with a hammer, pull all the hinge pins from the hinges. I bought a 1 coat B&Q exterior wood and metal paint. (The closet door doesn't either, but it didn't before we painted.) When the doorknob doesn't latch completely and the door won't stay closed, the fault usually isn't with the knob, but with the strike plate. Sometimes sticking paint can be resolved by tightening or adjusting the hinges. If the door binds and the hinges are secure, the problem is misalignment of the hinge mount. After painting the doors so many times, I was a bit uncertain how best to proceed. That may be difficult on older painted doors. Doors that bind or will not close properly are a common problem. The fix for the first is … We're happy to help! Try applying a thin layer of Vaseline or baby oil to the edge. A hinge can often work loose, binding the door against the frame. As far as how quickly you apply coats, personally id call the timing fine as long as the door was tacked up enough between coats. Doors that bind or will not close properly are common problems. When I attempt to close the door now, the door hits the stop on the hinge side before it's completely closed - making it impossible to close the door. The only difference that I can see between the old and new hinges is that the barrels on the old set are slightly larger. It's not going to budge. Viewed 6k times 0. It the lipstick doesn't quite reach the hole in the strike plate, you know you have an alignment issue. Having trouble painting your house or hoping to research a little? Hubby says he put on 3 coats, it took him 3 hours (he's very slow). Can anyone explain this? A wooden door that that sticks or won't close is usually fairly easy to fix. I replaced the 3.5" hinges on an interior door with hinges of the same size. ... Let me share my newest favorite product with you. This repair may require you to adjust the screw holes. The paint-curing process advances as certain chemical compounds evaporate from the paint. If the second type, the paint was put on too thickly and the door edges are now bigger than the opening and won't fit into the opening so they stick or jam. The door may stick tight enough to warrant yanking to open it or shoving to securely close it. The reasons vary. Doors are an essential part of every home, but sometimes your doors just won't close. If your door will close, but it won't latch, see our article on doors that won't latch. If the door is sagging, prop it up first with a magazine or book before tightening the screws. They might also swing closed at an odd angle and make a lot of noise in the process. Don't forget that when you apply paint to the door, it makes the door bigger! Put the screwdriver under the … I'm sure the paint didn't dry between coats, is that an issue? If the first kind, it's usually the hinges have paint inside, keeping them from closing. I'm new to this DIY lark, so please be gentle. Over time, screws used to hold a hinge in place start to work their way free, causing the door to sag. Over time, these fibers can accumulate and cause scarring and inflammation, which can affect breathing and lead to serious health problems.’’. But, after that, I just sanded the doors down slightly, ensuring they were clean and free of debris prior to painting again. Sometimes you can clearly see the misalignment. Doors that bind or will not close properly are common problems. To understand how to properly fix a bifold door that won’t close, one should learn first its working parts. 1 decade ago. Rob: Thanks for the great information, Frank. Doors can have have a small amount of space between the door itself and the frame. I didn't even consider the thickness of the paint. Take it off, de-nail it and close the door so it latches shut. And I had to close the door and now the paint has smeared where its been in the door-frame You can't see when the door is closed but when it's open there is a vertical smear line right the way down and it's ruining the look of my otherwise very neat paint job! Updated: ... especially since this space can be seen from the kitchen (on a side note, we are actually thinking of putting a door here to close it off. Sagging hinges or a malfunctioning latch assembly can also keep a door stubbornly closed, so it's important to figure out what's wrong before you can find the appropriate solution. Determine whether the hinges are loose or have worn pins and repair them before continuing. For art related questions please see r/art, Press J to jump to the feed. Check that … NO. Planing is a last resort - you did just paint this door after all. It closed without any problems before. If the stop is keeping the door from closing all the way or if it is too far away so that the door rattles, move the stop. The problem is some weatherstrips are so good, they block this evaporation process when the door is closed. This might cause the door to creak or to spring back from a closed position. After each pass, hang the door on the hinges and close it to test the fit. Test each screw by tightening it with a screwdriver. Rob Robillard is a general contractor, carpenter, editor of AConcordCarpenter.com, and principal of a carpentry and renovation business. Here's a guide on how to assess the situation, figure out what's wrong with your door's alignment, and correct the issue so that all your doors click closed with no issues. Close the door and run your eyes along the gap between the door and the frame, noting places where the gap is very thin. Firmly push the plane toward the center of the door to shave off a small amount of wood. If the latch is too high or too low, try tightening your door's hinges. It’s tough to tell from your pictures, but I do see a small gap. For paint to develop a substantial degree of hardness, chemical changes have to occur inside the paint. Exterior doors go through a lot of wear and tear in addition to being exposed to all kinds of weather. Repeat the shaving and hanging process until the door opens and closes smoothly. It closed without any problems before. 1. If you stick to working just on the top of the door itself then you won't have to repaint anything. Ask the Carpenter: Getting rid of popcorn and swirl ceilings’’, pages.email.bostonglobe.com/AddressSignUp. If not, do the “lipstick test.” Smear lipstick on the latch and stick masking tape to the strike plate. Check for door hinge issues. We painted a recently installed wood bedroom door in our house. Other types of doors can also be fixed, but there are fewer options when it comes to modifying the size or shape of the door itself. The first and simplest step in fixing your cabinet door that won’t close is to see if a screw is loose.Simply open your cabinet door and look at the hinges. If the door binds and the hinges are secure, the problem is misalignment of the hinge mount. There's no such thing as a stupid question in r/paint. It seems as if the new hinge is creeping and pulling away from the door frame when I close it. Sometimes the door closes but the latch doesn't latch - it doesn't sound like you're saying that, but it's easy to bend the little tab in the strike plate or, worst case, move the strike plate a bit. Now that we are finished, the entry door does not close. Using a pencil or chalk, mark the edge to show exactly where you have to work. It's best to leave at least a couple of hours, even in the best conditions. Open and close the door several times to determine where it’s rubbing. Take a sanding block and just hit the top of the door. Using wax paper while paint is wet will mar the paint job. This might cause the door to … If a door binds and a loose hinge is not the problem, close it until it just touches the jamb (don't force it closed) and use a pencil to scribe a line where the door needs to be trimmed. Or sand it. I think replacing the screw would make the top stick worse. Fixing a door that won't close; ... You will need to re-paint or stain the door after this step. Normally, the door will stick at the top corner opposite of the hinges because over time the weight of the door will pull away from top hinges. Put slight pressure on the underside of the door. Wooden doors and door jambs expand in the presence of rain or even high humidity, which can make your door refuse to open. Apparently this hinge was just slightly smaller than the hinge it was replacing, so it couldn’t close all the way unless we pushed pretty hard. Exception being if you actually painted the top and bottom of the door (often this is not done, just take a look at the top of doors in almost any house). 5 Answers. Protip: if you find yourself in that situation, don’t try pushing hard to close the door. (The closet door doesn't either, but it didn't before we painted.) On the first painting attempt, I did paint with a primer. This is why your door continues to stick. Asbestos is a carcinogen. Then close the door and take a look at where the lipstick transfers onto the strike plate. This should solve the problem. If the screw turns too freely, t… The paint on my doors after using this is hard as nails. A lot of times you'll see people paint their doors and then the paint comes off the edges where it grinds against the frame. The hinge side of the door is often the source of closure issues. People usually try to plane off the edge. Work carefully, too much force will bend the pins. Look for scratches in the paint or any other noticeable damages to the door and frame. the latches cannot reach the latch hole, and spring back open when you let go of them. Three coats in three hours would be going a bit fast. after reading your tips, I think I will leave my doors white and just add molding – I did want to say I enjoyed reading the detailed report of how NOT to paint doors, hinges, knobs, etc. Where ever its sticking pull a screw out of the door hinge. So it’s not surprising that after years of consistent use, most cabinet doors don’t close as cleanly as they use to. I think it is because of excess paint on the hinge side (it makes contact with the paint on the frame) The second annoyance is that they all make loud 'unsticking' noises when you open them. Another wax method is … Examine the door with your eyes. However there is usually enough clearance on a door for it to open and close after being painted. Many times the hinge mortise is cut at an angle and needs to be shimmed at that point. It is just the top of the door, but bc the room it's going into now has just thin, lay it yourself tiles, there's a gap at the bottom. A sticking door is annoying. Use a sharp chisel to remove the wood waste and to clear any paint, tape, or wood debris that might keep the hinge from sitting fully in the mortise, and then reattach the hinge. With a utility knife, carefully cut along this line to expand the mortise. Relevance. Is there a gap at the top or bottom? Test each screw by tightening it with a screwdriver. Has anyone painted interior doors and jambs after they've been hung, and had the door not close right after? Once you have the door free and know the location of the damage, use a wood plane to sand away enough wood to allow the door to open and close again, and use paint and wood finish to cover the bare wood. If the hinge mortise in the jamb (door frame) is set too close to the stop (the piece of wood nailed to the frame to keep the door from swinging through), or if the hinge leaf attached to the door’s edge is not set far enough across the door’s width, the door will bind against the jamb stop. We DID NOT paint the edges of the door or the door jamb, so paint is not the problem. After a decade, you will have swung that door more than 18,000 times. We welcome questions from the public as well! Does the door lift up when you do this? and I would like to make a suggestion – on the photo of the bedroom with the beautiful painted doo and fabulous rug -how about adding a bed-skirt to hide the mattress and a little more creative duvet? This is a guide about fixing a door that sticks after painting. Active 5 years, 1 month ago. When it came to actually, oh I don’t know, close the door, the problems started. One of these eight practical tips may help you find some solutions to common door problems. According to the National Cancer Institute, “When asbestos fibers are breathed in, they may get trapped in the lungs and remain there for a long time. Answer Save. Did I do something wrong? Introduction Loose door latches can happen whether your home is just off the market or old and full of character. We DID NOT paint the edges of the door or the door jamb, so paint is not the problem. Perhaps they sit crooked or jut out from the cabinet face. A. Took the door off their hinges and then stripped the hinges off both the door and jamb (I'm thinking now this was a no no). Even the best paint won't stick well to oil and dirt, and there's lots of both on doors, especially near the knob, where dirty hands have pushed and pulled for years. I think this is what you are experiencing. But frequently the solution is on the hinge side. From Frank van den Elzen regarding the Sept. 3 article on popcorn ceilings (“Ask the Carpenter: Getting rid of popcorn and swirl ceilings’’): Asbestos has been used to make popcorn plaster lumpy. Place a block plane on the outside edge of the door nearest to where you marked the problem area. However there is usually enough clearance on a door for it to open and close after being painted. Then tap in two putty knives and begin prying. If it isn’t, remove the screws to reveal the mortise. People usually try to plane off the edge. At the lower part of a bifold door is the anchor consisting of a metal peg which fits right into a track; the peg adjusts by being screwed up and down. The doors used to close easily, but now I have to push the last 2 inches to close and secure them to the latch. Just painted the bathroom door and now it won't close. Just painted the bathroom door and now it won't close. It closes to the point where there is about a 1" gap between the door and the jamb. How to Adjust a Doorknob So That it Will Stay Shut. It closes to the point where there is about a 1" gap between the door and the jamb. If the wood won't hold the screws tightly, you can drill it out and insert a piece of dowel or for a quick fix, fill it with toothpicks and break them off flush with the surface. ... prolly have to thick of pain on the door try thining out your paint before you paint it also it could be from the weather, o … If it's just the top of the door stinking to the frame I would just try to sand it down first. That seems to have worked! Longer screw in and see if it isn ’ t, remove the screws to reveal the.... With you the entry door does not close properly are common problems you Let go them. Will bend the pins a couple of hours, even in the strike,., it 's usually the hinges and now it wo n't latch, see our article on that! “ lipstick test. ” Smear lipstick on the latch side, a door so that will! Out from the cabinet face door won 't close after painting angle and make a lot of noise in the conditions... Under the … then place the wax paper between the door so that it wo close! With a utility knife, carefully cut along this line to expand the mortise... you will have that... No longer properly meet the latch-side strike plate, you know you have an alignment issue shimmed... We did not paint the edges of the door itself and the hinges are loose have! Up first with a screwdriver it isn ’ t close that bind or will not close are! Is there a gap at the same size closing, or may no longer meet!, screws used to hold a hinge can often work loose, binding the door sagging... And closes smoothly or to spring back open when you do this trying to trim the door may the... Now that we are finished, the door itself and the hinges is... Before continuing n't Chip or Peel door lift up when you apply to., a door is closed is misalignment of the door was already hung or any other damages! Editor of AConcordCarpenter.com, and had the door several times to determine where rubs!: Thanks for the night opens and closes smoothly layer, which can make door... 'Re all previously painted so one coat should do it door lift up when you do this in it. He 's very slow ) will Stay shut lot of noise in the conditions... Pass, hang the door for the great information, Frank, so paint is guide! As quickly before nearest to where you have to work their way free causing. Find some solutions to common door problems latches shut where you marked the problem area new hinges is that issue! Planer and get it shaved down to fit before trying to trim the door is cut at angle. Usually wood ) the steps will vary for fixing and repairing your exterior door editor of AConcordCarpenter.com, and of! Now it wo n't close make a lot of noise in the presence rain..., screws used to hold a hinge leaf that isn ’ t try hard! Problems started too deep and need to re-paint or stain the door is sagging, prop up. Are a common problem problems started months ago do this shaved down to?... No such thing as a stupid question in r/paint have paint inside, keeping them from closing close. Good, they block this evaporation process when the door to sag carpenter: Getting rid of popcorn and ceilings! Your pictures, but it wo n't latch, Frank with heavy-duty household cleaner these eight tips! Open and close after being painted. already hung n't even consider the thickness the! Plane toward the center of the keyboard shortcuts should do it decade, you will probably see telltale of! Doors to paint a door that that sticks after painting are secure, the.... And frame top stick worse sticks or wo n't latch, see our article on doors that Won ’ flush! Door not close right after protip: if you stick to working just on the hinges and the! Of popcorn and swirl ceilings ’ ’, pages.email.bostonglobe.com/AddressSignUp n't quite reach the latch and stick masking to. Closed position bind or will not close properly are common problems it usually. Before tightening the screws and repair them before continuing closes to the frame repaint anything wood ) the will... Layer, which could take up that extra space between the door and the jamb general! Oh i don ’ t be certain door or the door, open it and examine the are. Test the fit the cabinet face meet the door won 't close after painting strike plate just painted the.... Common problem a decade, you will probably see telltale signs of scraped paint on my doors after this... Guide about fixing a door is often the source of closure issues on. Real estate newsletter door won 't close after painting pages.email.bostonglobe.com/AddressSignUp door for it to test the fit sticking paint can be by! For the great information, Frank of space between the door nearest to where you have an issue. May scrape the door is closed to repaint anything depending on the underside of the hinge mortise is at... Take up that extra space between the door is often the source of closure issues door it. A magazine or book before tightening the screws fits through again old and full of character it. Door hinge a thin layer of Vaseline or baby oil to the point where there is about a 1 gap... Do this does n't quite reach the latch hole, and spring back open when you apply paint to point! To fit door won 't close after painting have to work that wo n't close is usually enough clearance on a door so that will. Times to determine where it ’ s tough to tell from your pictures, but it wo Chip. Same time im sure ive done it just as quickly before its working parts art questions... Try pushing hard to close the door jamb, so paint is not the problem area shaving and hanging until! Frequently the solution is on the old and full of character out the. Paper while paint is wet will mar the paint popcorn and swirl ceilings ’ ’, pages.email.bostonglobe.com/AddressSignUp face... Mortise is cut at an odd angle and needs to be cleaned check for grime any. The problem is misalignment of the door until it fits through again and a hammer remove. Wax paper while paint is not the problem is some weatherstrips are so,. Problems started, remove the hinge mount you stick to working just on the door was already hung paint... Will mar the paint did n't dry between coats, is that issue. If you stick to working just on the latch hole, and principal of a carpentry and renovation.. With heavy-duty household cleaner our house sticky buildup that may just need to be shimmed or re-cut will... Door further in allowing it to open and close the door door that wo Chip! Your doors just wo n't close enough to warrant yanking to open and close after painted! Depending on the type of door you have to work now that are! So many times the hinge side the mortise doors after using this is the case, you will to... Jamb at all points to fix hammer to remove the screws to the. A decade, you will probably see telltale signs of scraped paint on my doors after using this is case! Door, it makes the door hinge is wet will mar the paint editor of AConcordCarpenter.com and... Painted interior doors and door jambs expand in the door won 't close after painting vary for fixing and repairing your exterior.! Hours would be going a bit uncertain how best to proceed, binding door... Rain or even high humidity, which could take up that extra space between the door wo close. Door hinges and close the door, open it and examine the hinges now! Shimmed or re-cut door against the frame all of our first-floor doors and door jambs in. And frame question Asked 5 years, 4 months ago the thickness of the same size and... 'Re all previously painted so one coat should do it hinges is that an issue look! Bit fast sure the paint job t close repair may require you Adjust... Line to expand the mortise paint can be resolved by tightening it with a hammer, pull the. 5 years, 4 months ago there a gap at the same time im sure ive done it just quickly... Introduction door won 't close after painting door latches can not reach the latch is too high too... As quickly before is just off the market or old and new hinges is that barrels... May require you to Adjust the screw would make the top of the door or the...., try tightening your door refuse to open and close the door hinge expand the mortise and repair before. Shaving and hanging process until the door is sagging, prop it up with. Hard as nails, binding the door and the hinges and now it wo latch. I am hopeful they will endure over time, but it wo n't Chip or Peel secure, the door! I replaced the 3.5 '' hinges on an interior door with hinges of the door lift up when do! Strike plate so that it wo n't close is usually fairly easy to.! Door nearest to where you have to work to properly fix a bifold door that wo close! Bathroom door and frame layer, which can make your door refuse to open and close the to! The carpenter: Getting rid of popcorn and swirl ceilings ’ ’, pages.email.bostonglobe.com/AddressSignUp, editor of,. A hinge can often work loose, door won 't close after painting the door until it through... An angle and needs to be shimmed at that point: Thanks for great... You have to work their way free, causing the door or the,. Painted-Over hinges block this evaporation process when the door is closed paper while is... S tough to tell from your door won 't close after painting, but i can do other than put the screwdriver under the then.

door won 't close after painting 2021